Optronics round light grommet # A45GB fits a 4-1/2-inch cutout and accepts a 4-inch round light such as # BUL43CB. This round white LED-type work light features 10 super diodes for bright high-efficiency lighting. This light is intended as a work light; it is not certified for use as a backup light. For a 2-wire pigtail lead you can use part # A45CB.
Thanks to the high-efficiency of this LED light you can use multiple lights without causing the same power draw demanded by incandescent types. view full answer...
It sounds like you are looking for lights like the POD Hazard LED Warning and Work Lights # RPPD110200. These function as warning lights in the event of a roadside emergency and also as work lights. The LED lights are capable of 40 hours of run time on 3 AAA Batteries # DU48QR. view full answer...
I have a similar solution that will work for you, but the light you mentioned won't have the Lumens you need.
The Optronics LED RV Interior Light # RVILL34 has 2 ratings. The raw output, unobstructed and in testing conditions the light can produce 920 lumen. The effective lumen output in real-world scenarios is 815 lumen. But the watts are low; 1.22 at 815 lumen.
This also has an easy to use switch on it for you to use. view full answer...
It sounds like you need a converter so the 3 wire system on your vehicle works with the 2 wire system on your new LED tail lights. If that is the case, you can use the Hopkins Tail Light Converter - LED Compatible # HM48847. This installs on your vehicle wiring to combine your vehicle's independent brake light and turn signal functions. view full answer...
If your RV wiring doesn't want to power the lights that means the issue is either the ground or the power since you have verified the lights work. You would want to use a circuit tester like part # PTW2993 to test the wires of the trailer with the correct taillight function on to determine which is the power wire and wire it accordingly to the lights of your trailer.
If that still doesn't activate the light then the issue is the ground wire. In that case you need to improve the ground... view full answer...
We carry a bracket that will work installing your trailer tail lights. The CE Smith Tail Light Bracket # CE26057AA, is a L-shaped bracket that will fit most stud mounts tail lights.
This bracket is more of an universal fit. Unfortunately, we do not have an exact fit for your model light.
If you think this bracket will not work for you, then I have attached a link that will take you to all the trailer lighting mounting brackets we carry for you to review. view full answer...
I do have an option for you, but we do not have fenders that already have the lights on them. We do have the Fulton Single Axle Trailer Fenders # F008574-2 which are white and work with wheels up to 14", so they will work with your 13" wheels.
You can then add a light using the Black Bracket and Single Wire Plug for Thin Line Series Trailer Clearance and Side Marker Lights # A65PB and the GloLight Thinline LED Trailer Clearance or Side Marker Light # MCL165RB for red or the GloLight Thinline... view full answer...
Curt offers a custom-fit adapter for the 2006 Porsche Cayenne that includes load resistors to allow the vehicle to pull a trailer with LED lighting. That item is part # C57003 and it is shown in the linked video. This adapter includes load resistors to allow vehicles like the Cayenne to properly activate LED trailer lights. view full answer...
The Optronics marker light, part # MCL66A24B is the only amber thin-line marker light we offer that is compatible with 24-volt systems. The # MCL13A2B would not work, as it would only work with a 12-volt system.
The lamp would mount directly to the trailer frame on 3 inch centers, and features a power and a ground wire. The lamp is also available in red as part # MCL66R24B. view full answer...
The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module # PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light.
If there is a specific light style that you are looking for just let me know and I can make some recommendations for you. view full answer...
The best solution is going to be with a larger size light if you can enlarge the hole you have like with the Optronics LED Backup Light for Trucks or Trailers # BUL11CB and grommet part # A45GB. You'll need to cut the hole out to 4-1/2 inches in diameter but you'll get a really bright LED setup that will work great. You'll also need a pig tail harness as well with part # A45CB.
We don't have anything that would fit a 2-1/2 inch diameter hole. view full answer...
All of the license plate lights we have that are listed as submersible are incandescent, not LED. We have Peterson light # M439K and Optronics light # LP97CB. Though the lights are submersible you will need to make sure the wiring connections are water-tight by using something like liquid electrical tape, # SWC50122. view full answer...
We do have the driver side light available, they are not universal. The correct light is the Peterson Trailer Tail Light w/ License Bracket # V457L. Unlike the # V457, this includes the license plate bracket and light. view full answer...
The Trailer Clearance and Side Marker Light # MCL48AB uses a three wire setup which means that the light has two light intensities. A lower intensity for the running light circuit and a brighter intensity that will come on when the brakes or turn signal is activated. The headlights do not need to be on for the blinker to work. I attached a review video for more info on this as well. view full answer...
Yes, we have simple trailer lighting install kits that simply plug into your 4-Pole connector. For your wood chipper I would recommend the Standard Trailer Light Kit with 25 foot Wire Harness, item # TL29BK. You will not need the side marker lights included with this kit so you can just eliminate them. We also have a kit designed for cargo carriers that would work well on your wood chipper, theetrailer License Plate and LED Tail Light Mounting Kit for Hitch Mounted Cargo Carrier Item #... view full answer...
There are no brackets made by Curt to attach driving lights but some driving lights we carry have their own mounting brackets that should work on the cargo basket # C18155 but you would probably need to drill into the basket to attach the lights. I have included a link to the driving lights we carry. view full answer...
The only color changing lights we currently carry would be LED strip lights like the Smart LED Light Strip # DIA86QR. These lights come with a remote, but can also be controlled using the LotusLanternX app on your smart device. These would not be compatible with your Alexa. view full answer...
The # A5TRSSB ring will not work with the GloLight LED Trailer Tail Light # STL101RCFB. The GloLight LED Trailer Tail Light # STL101RCFB already has a built-in ring which prevents you from using the stainless steel ring.
What you would need to do is use the GloLight LED Trailer Tail Light # STL101RCB with the Stainless Steel Trim Ring for Optronics STL101-Series Trailer Tail Lights # A101TRSSB. view full answer...
I spoke to my contact at Optronics and the Sealed 3-Light Truck Trailer Identification LED Light Bar, # MCL84RB, is not offered in amber. However, we do have a couple of light bars that may work for you.
We offer the 3-Light Truck and Trailer Identification Light Bar with White Base - Amber # MC99AB, but this one is not submersible.
I have included a couple of short videos for you. view full answer...
The RoadMaster Bulb and Socket Set for Tail Light Wiring Kits, # RM-155-2 is not vehicle specific. This is designed to work with Roadmaster Tail Light Wiring Kits such as # RM-155 if needed. The full kit that includes the connectors and wire is # RM-155 for incandescent. If your vehicle has LED lights, you will need # # RM-152-LED.
To properly install you will need a silicone sealant such as # LT37467 and drill a 1 inch diameter hole in the rear of your taillight assemblies. Ensure you... view full answer...
Go To Results